Lexmark 302 Manuel d'utilisateur Page 186
- Page / 274
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Printer Verification
You can test general print quality and the wires in the print head by
using the Printer Verification test. This test prints nine horizontal
lines using each wire on the print head. After these nine lines have
printed, several lines of data processing (DP) characters are printed
followed by several lines of near letter quality (NLQ) characters.
To test print quality, follow these steps:
1. Enter the Operator Print Tests (see “General Test Instructions”
on page 4-1).
The printer displays
2. Press Scroll↓ or Scroll↑ until the printer displays
3. Press Enter or Start to begin the test.
The Ready indicator goes on and printing begins. The
verification printout is complete when the Ready indicator goes
off.
OPERATOR PRINT TESTS
Printer Demonstration
OPERATOR PRINT TESTS
Printer Verification
4-12 User’s Guide Model 302
- 4232 Printer 1
- Model 302 1
- User’s Guide 1
- Contents 5
- Contents vii 9
- User’s Guide Model 302 10
- Electronic Emission Notices 11
- Notices xi 13
- Trademarks and Service Marks 14
- Safety Information 15
- How to Use This Guide 17
- 18
- Publications 19
- print head carrier 30
- power cord 32
- platen rod 42
- Blue Form s G uide/ 45
- Form s Sensor 45
- Blue Tractor Door 46
- Tractor Pins 47
- Platen Rod Surface 49
- First Print Line 49
- Blue Forms 62
- Tension Knob 62
- Decreasing Forms Tension: 63
- Increasing Forms Tension: 63
- Access Cover 66
- Metal Bar 74
- Blue Forms Guide/ 80
- Forms Sensor 80
- R ight Tractor Assem bly 81
- Blue Locking 81
- R ight Tractor 81
- Tea r Bar 98
- Unloading Forms 103
- Blue Tractor Doors 104
- A ccess C over 105
- Paper Door 105
- Right Roller Assembly 108
- Bottom of Forms Device 108
- Blue Sliding Guide 108
- Blue Locking Lever 108
- Finger G rips 109
- Platen R od 109
- Changing the Paper Door 110
- Paper D oor 111
- Hinge Pin 111
- Preparing to Load Forms 112
- 115
- Adjusting the Print Quality 120
- IBM 4232 Printer Model 122
- Forms Guide 124
- Form s G uide 129
- Finger Grips 134
- Using the Acoustic Cover 136
- Removing the Acoustic Cover 136
- Rear View 137
- Computer 138
- Adapter Cable 139
- IBM part num ber 139
- Parallel 139
- Interface C able 139
- Attaching a Serial Cable 141
- S/N XX-XXXXX 144
- TYPE 4232-XXX 144
- Power Switch 145
- Acoustic Cover 147
- Access Cover 147
- Front Paper Door 147
- Forms Guide/Forms Sensor 148
- Platen Rod 150
- Operator Panel 151
- Instructions 154
- IBM 4232 155
- Operating States 156
- Ready and Not Ready 156
- Top of Forms Device 158
- Bottom Metal Bar 158
- Tensioner Plates 158
- B o tto m M e ta l B a r 159
- To p o f F o rm s D e vice 159
- Tear Bar 159
- Auto Sheet Feeder Device (F4) 161
- Caring for Your Printer 163
- Starting a Print Job 164
- Ribbon C artridge 167
- Removing the Ribbon Cartridge 168
- Ribbon G uide 169
- Remove Yellow Clip 170
- Blue Ribbon Advance Knob 170
- Blue Slotted O pening 171
- MetalPost 171
- Blue R ibbon Advance Knob 173
- General Test Instructions 175
- Printer Demonstration 177
- Top of Form Alignment 178
- Chapter 4. Tests 4-5 179
- Left Margin Alignment 180
- Chapter 4. Tests 4-7 181
- Printer Configuration 183
- Printer Verification 186
- Chapter 4. Tests 4-13 187
- Bidirectional Adjustment 189
- Chapter 4. Tests 4-17 191
- Introduction 194
- Guideline for Training 195
- Information 197
- Panel Instructions 198
- Customer Responsibility 199
- A-8 User’s Guide Model 302 200
- Appendix B. Problem Solving 201
- Status Codes 203
- Appendix B. Problems B-5 205
- Appendix B. Problems B-7 207
- IBM 4232 Printer 208
- Paper Present 209
- 221
- 221
- Problem List Index 223
- Forms Device Inspection 224
- Problem List 227
- Miscellaneous Problems 236
- Appendix C. Forms Information 237
- Forms Maximum Minimum 238
- Dimensions 240
- Thickness 240
- Composition 241
- Performance Considerations 241
- IBM 4232 241
- Additional Forms Restrictions 242
- Positioning Forms 244
- Noise Emission Values 249
- D-2 User’s Guide Model 302 250
- Serial Attachment 251
- Cable Configurations 253
- E-4 User’s Guide Model 302 254
- RS-422A 255
- Parallel Attachment 256
- Glossary 257
- X-2 User’s Guide Model 302 258
- Glossary X-3 259
- X-4 User’s Guide Model 302 260
- X-6 User’s Guide Model 302 262
- X-8 User’s Guide Model 302 264
- (continued) 265
- (continued) 265
- Name Address 271
- Company or Organization 271
- Phone No 271
- &@rcfaddr(1) 272
- SA24-4386-01 272
- Part Number: 56G9390 274
- Printed in U.S.A 274
- SA24-4386-ð1 274
Produits connexes et manuels pour Imprimeurs Lexmark 302
Imprimeurs Lexmark 1200 Manuel d'utilisateur
(208 pages)
(208 pages)
Imprimeurs Lexmark 4059-XXX Manuel d'utilisateur
(347 pages)
(347 pages)
Imprimeurs Lexmark 258x Manuel d'utilisateur
(120 pages)
(120 pages)
Imprimeurs Lexmark Z600 Manuel d'utilisateur
(69 pages)
(69 pages)
Imprimeurs Lexmark 30E Manuel d'utilisateur
(144 pages)
(144 pages)
Imprimeurs Lexmark 5025 Manuel d'utilisateur
(171 pages)
(171 pages)
© 2020, manymanuals.fr. Tous droits réservés | 1.971 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels